Channel Steel Floors

Steel-MAX has designed a special range of stumps to suit cold rolled channel bearers and lipped channel joists, such as Stramit C sections or similar.

Stump bases are in the form of a U-shaped bracket, for multi-position and multi-angle connection to footings. Special moment base plats are available for mezzanine floors and where maximum bracing stability is required.
Stump tops fit any wall thickness tube and are telescopically height adjustable up to 75mm. They have vertical fin plates to suit B180, B240 and B280 C bearers. They provide maximum support and hold-down through the bearer’s web and are also designed to keep perimeter bearers as close to the outside of the building as possible.

For more information, see Steel-MAX Channel Floor Details.

Supported Stump Systems

Downloads

Stramit Steel-MAX Floor Framing System (ZIP)

Capacities

Steel Stump Tubes

Minimum grade C350.

SHS	Max. height
75×2.0	= 1.8m
75×3.5	= 2.5m
75×5.0	= 3.4m

Stump tops to steel stump tubes

Connection	Shear capacity Vu
2×14-20 Teks	14.7kN
4×14-20 Teks	29.4kN
8×14-20 Teks	58.8kN
16×14-20 Teks	117.6kN
20×14-20 Teks	147.0kN
1 / M12 bolts	24.2kN
2 / M12 bolts	48.4kN

Minimum stump top and post Yield Stress fy = 300 MPa; Minimum bolt Yield Stress fy = 400MPa. Notes:

All shear capacities are governed by the screw/bolt shear capacity.
Calculations based on a minimum post wall thickness of 2.0mm.
Tek screws to be installed in accordance with the manufacturer’s specifications
Screws and bolts may be combined to achieve reduced shear capacities, using the appropriate reduction factors for each connection type.

Stump top to Stramit bearer connection

Minimum stump top, fin plate Yield Stress fy = 300 MPa; Minimum bolt Yield Stress fy = 400MPa.

Connection	Shear capacity Vu
2×14-20 Teks	9.2kN
4×14-20 Teks	18.4kN
6×14-20 Teks	27.6kN
1 / M12 bolts	10.2kN
2 / M12 bolts	20.4kN

Notes:

All shear capacities are governed by the hole capacity of the LSB’s web and not the screw/bolt shear capacity.
Calculations based on a minimum web thickness of 1.5mm, minimum Tensile Strength (fu) = 490MPa and minimum Yield Stress (fy) = 380MPa.
Tek screws to be installed in accordance with the manufacturer’s specifications
LSB members to be fully restrained against lateral displacement of both flanges and twisting about the longitudinal axis.

Bracing brackets

Connection	Bracing capacity
4×14-20 Teks	15kN ( 12mm rod )
M16 bolt	22kN ( 16mm rod )

Moment base plates

100x100x4.0 Moment Base Plates have an ultimate bending moment capacity of 5.2kNm, subject to the following:

Must be fixed to a footing or slab with a minimum compressive strength of 25MPa with 4 / M12 chemset anchors, fixed with a minimun distance between the centre of the bolt and the edge of slab of 50mm.
The supporting structure should be assessed by the project engineer to ensure that it is structurally capable of withstanding both the moment and vertical loads expected.
The Moment sleeve must be fixed to the supported post with a No.10 Tek screw in each of the four faces of the sleeve.
The gap between the sleeve and the supported post must be adequately sealed to prevent moisture ingress between the two members.

Other Information

1. SMART STUMPS

Steel-MAX has designed a special range of stumps specifically to suit “C” channel bearers.

STUMP TUBE:

The stump tube is 75×75 Gal. SHS and will vary in wall thickness to suit load requirements.

STUMP BASES:

Stump bases are in the form of a “U” shaped bracket, for multi-position and multi-angle connection to footings.Special “Moment Base plates” are available for mezzanine floors and where maximum bracing stability is required.

STUMP TOPS:

Stump tops fit any wall thickness tube and are telescopically height adjustable up to 75mm. They have vertical “fin plates” to suit B180, B240 & B280 “C” bearers. They provide maximum support and hold-down, through the bearer’s web and are also designed to keep perimeter bearers as close to the outside of the building as possible. Special screw adjustable tops are also available and are particularly useful for reactive soil conditions. Centre-fin tops support back-to-back bearers so that the centre line of the stumps matches the centre of the abutting bearers. Multi-top stumps are also available for some applications where bearers can be joined at “T” intersections and90 deg corners.

POST SLEEVES:

Post sleeves may be used to carry bearers which need to be fixed to the face of a verandah post, or a higher stump which continues up to support a different level floor, such as in split levels.

2. BRACING:

“U” shaped bracing brackets are connected to stumps to carry either 12mm or 16mm threaded bracing rod, to form sub-floor cross bracing sets. They yield up to 15 kN or 22 kN capacities respectively.

3. CONNECTORS:

“L” fixed angle brackets may be used at 90 deg joist to bearer or bearer to bearer connections, where extra strengthening is required at the connection.

They are also useful when connecting trimmers around stair voids.

Hinged “H” brackets can be used at angled connections, similar to the “L’ brackets.
Joist connector brackets are in the form of an angle, which are usually fixed vertically to the webs of both the bearers & joists, in a joist-on-bearer application.

They help support both members and provide good hold-down and lateral stability to joists.They are available in 200mm and 295mm lengths.The 200mm brackets can also be used to fix the ends of J240 & J280 “C” in-plane joists to bearers at “T” intersections when other fixing methods are difficult or impractical.

4. DURABILITY:

All Steel-MAX products have corrosion protection, such as Dacrotising ( refer to web site at:- http://www.dacro.co.kr/eng-3.htm ) as well as Galvanizing and Galvabond finishes.Refer to your channel manufacturer’s durability selection criteria and protect all exposed members as per the Steel-MAX corrosion protection recommendations.

5. TECHNICAL SUPPORT:

Contact Steel-MAX via the web site, email, phone or fax; or ask your Steel-MAX distributor.

6. ENGINEERING:

Engineering design and certification is provided by H.R. Design Group P/L (Hunt Robinson Engineers) for the Steel-MAX products. H.R. Design has also produced the very useful S3R software for Stramit. A copy of the standard letter of certification is available from the Steel-MAX web site. Steel-MAX does not provide individual job certification, footing or sub-floor bracing designs, or certificates of compliance. These are generally site specific and should be provided by the project engineer.

7. JOB DESIGN:

When using Steel-MAX products in conjunction with Stramit sections; use the Stramit S3R design software to determine the most suitable Stramit member sizes, or ask your Stramit representative for assistance from Steel-MAX to offer a floor design solution for your project, including all necessary Steel-MAX companion products.

8. FIXINGS:

Refer to the Steel-MAX load capacity tables on page 10, (provided by the H.R. Group) and have your project engineer specify your individual job requirements. However; for uniformly loaded domestic applications, consider the following as a guide only :- Stump bases to stump tube = 6 / 14 g hex teks ( 3 in each face ) Stump tops to stump tube = 8 / 14 g teks up to 8 m2 of floor area carried by the stump, then 1 / screw per m2 or 1/M12 bolt per 5 m2 of area extra over the first 8 m2. Sleeves to tube = 8 / 14 g teks per sleeve. Bracing brackets = 4 / 14 g teks per brackets for 12mm rod and 1 / M16 bolt per bracket for 16mm rod. “L” & “H” connector brackets = 8 / 10 g teks for joist to bearer connections and 8 / 14 g teks for bearer to bearer connections. Joist connector brackets = use 6 / teks per brackets ( 3 in each member ) Use 10 g. teks for 200mm brackets and 14 g. teks for 295mm brackets.

9. AVAILABILITY:

All Steel-MAX products are available from Steel-MAX Distribution by contacting us here or by emailing direct to info AT steelmax DOT com.au Steel-MAX “Companion products” to the Stramit Residential Flooring System are available from your participating Stramit Building Products supplier.

10. APPLICATION DETAILS:

The suggested methods of using Steel-MAX products with “C” channel sections and may act as “Companion products” to Stramit “C” channel sections for a restricted number of common construction applications. The information contained within this document or any other provided by Steel-MAX, does not represent, form or replace any other system requirements specified for any other floor framing system. All information shown, enclosed and contained within this and associated documents represent suggested methods of using Steel-MAX components in conjunction with “C” channel sections, such as Stramit “C” sections or similar and may not suit your particular job requirements and application. We offer design solutions as a suggestion, for the consideration of the customer and his project engineer. It is imperative that the customer’s project engineer looks at the suggested details and either incorporates them into his whole job structural design, or alters them to suit his requirements. It is always possible that there could be influencing elements within the structure, that we are not aware of, which could effect and alter the following suggested details and information.